Installation Guide
Tools Needed:
- Phillips screwdriver
- Wall anchors (if not mounting on wall)
- Batteries (AAA x 2)
- Level
- Pencil for marking
Step-by-Step Installation
- Choose Installation Location: Select a location within 8 meters of the indoor unit, away from direct sunlight and heat sources.
- Prepare Remote Holder: Attach the remote holder to the wall using screws and wall anchors if needed.
- Insert Batteries: Open the battery compartment and insert two AAA batteries, observing correct polarity.
- Mount Remote Controller: Place the remote controller into the holder until it clicks into place.
- Initial Setup: Point the remote at the indoor unit and press the ON/OFF button to establish communication.
- Test Functions: Test all basic functions including temperature control, mode selection, and fan speed adjustment.
- Final Check: Ensure the remote responds properly from all intended locations in the room.
Specifications
| Model Number | BRC1D52 |
| Type | Wireless Remote Controller |
| Color | White |
| Compatible Systems | Daikin Split Systems, Multi-split Systems |
| Operating Range | Up to 8 meters (line of sight) |
| Display Type | LCD with backlight |
| Power Source | 2 x AAA batteries |
| Battery Life | Approximately 1 year (normal use) |
| Dimensions (HxWxD) | 85 x 60 x 20 mm |
| Weight | 85 g (including batteries) |
| Operating Temperature | 0°C to 50°C |
| Signal Type | Infrared (IR) |
Warranty Information
- Remote Controller Warranty: 1 year parts and labor
- Batteries: Not covered under warranty
- Additional Coverage: Extended warranty available with system purchase
For warranty service, contact Daikin Customer Service at 1-800-DAIKIN-1 or visit Daikin.com
Key Features
Wireless Operation
Infrared wireless technology allows convenient control from anywhere in the room without the need for direct wiring to the indoor unit.
LCD Display with Backlight
Clear LCD display shows all settings including temperature, mode, fan speed, and timer settings with automatic backlight for low-light conditions.
Multi-Function Control
Complete control over all air conditioning functions including temperature, operation mode, fan speed, airflow direction, and timer settings.
Energy Saving Mode
Econo mode optimizes operation to reduce energy consumption while maintaining comfort levels.
Quiet Operation
Quiet mode reduces operational noise for nighttime use or in environments where minimal noise is preferred.
Auto Swing Function
Automatically adjusts louver direction for optimal air distribution throughout the room.
Operation Modes Explained
Cooling Mode
Standard air conditioning mode for hot weather, with temperature range 18°C - 32°C
Heating Mode
Heat pump operation for cold weather, with temperature range 16°C - 30°C
Dry Mode
Dehumidification function that reduces humidity without significant cooling
Fan Mode
Circulates air without heating or cooling, with multiple fan speed options
Auto Mode
Automatically selects cooling or heating based on room temperature
Turbo Mode
Rapid cooling or heating for quick temperature adjustment
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not working | Dead batteries, blocked signal, too far from unit | Replace batteries, ensure line of sight, move closer to indoor unit |
| Display is blank | Batteries installed incorrectly, battery compartment issue | Check battery polarity, clean battery contacts |
| Indoor unit not responding | Signal interference, indoor unit power issue | Remove obstacles, check indoor unit power supply |
| Buttons not responding | Battery low, remote malfunction | Replace batteries, reset remote by removing batteries for 1 minute |
| Backlight not working | Backlight disabled, battery saving mode | Check settings, replace with fresh batteries |
| Incorrect temperature reading | Remote sensor issue, location too hot/cold | Move remote to better location, check sensor calibration |
Error Codes Displayed on Remote
- E0: Room temperature sensor error - Check sensor connection
- E1: Indoor unit PCB error - Contact service center
- E3: Drain pump error - Check drainage system
- E5: Overload protection - Wait 3 minutes and restart
- E6: Communication error - Check wiring between units
- EA: Outdoor unit error - Contact service center
Manual Downloads
Current Model Manuals
BRC1D52
Standard Wireless Remote
BRC1E52
Enhanced Wireless Remote
BRC1F52
Wi-Fi Enabled Remote
BRC1G52
Commercial Remote
Popular Previous Models
BRC1C52
Basic Wireless Remote
BRC1B52
Standard Remote (Previous Gen)
BRC1A52
Original Remote Controller
BRC1D42
Compact Remote